Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
Product Description of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
The H 250 flowmeter for measurement of the volumetric or mass flow rate of liquids,gases and steam is an all-metal flowmeter that operates on the float measuring principle. The flow-dependent vertical position of the float in the measuring tube
is transmitted by a magnetic coupling system to the scale in the indicator part.
The flowmeter is installed in a vertical pipe run, with flow from bottom to top. Owing to its rugged design, the H 250 variable-area flowmeter is particularly suitable for difficult applications and environmental conditions.
In the M9 indicator, the vertical position of the float is transmitted to the pointer/magnet system, and the flow value indicated directly on the scale.
H 250 of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
… flow measurement can’t be easier or more flexible
one all-metal flowmeter
four electrical add-on devices:
ESK 2-wire transmitter
ESK-Z electronic totalizer
ESK3-PA Profibus PA transmitter
K switching contacts
four materials for the measuring section: stainless steel, Hastelloy,ceramic-PTFE, PTFE
Special technical features of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
Measuring sections
H 250 RR
● of highly corrosion-proof stainless steel
● rugged all-metal design
● all built-in parts replaceable
● all pressurized welds suitable for x-ray examination
● float damper of aluminium oxide (Al2O3), PEEK or stainless steel,also retrofittable
● the measuring section can be equipped with a heating jacket
H 250/C (ceramics/PTFE)
● suitable for most acids and alkalis
● very good long-time stability
● high-temperature design up to 250°C
● all wetted parts made of ceramics (Al2O3) and/or PTFE
H 250/F (food)
● all-metal flowmeter, no blind spots
● surface roughness of wetted parts Ra ≤ 0.8 µm
● CIP and SIP cleanability (200°C)
● materials in conformity with FDA standards
● connections: Tri-Clamp, DIN 11851, flanges, etc.
● EHEDG tested / USA 3-A certified
Indicator
M9 indicator/modular standard and EEx e
● direct-reading flow indicator
● indicator with extension piece (HT version) for high process temperatures
● electrical signal output (ESK II) with HART® communication in 2-wire technology (can also be retrofitted)
● communication interface PROFIBUS-PA, as an alternative to ESK II
● max. 2 limit switches (K) adjustable on the scale (can also be retrofitted)
● flow totalizer ESK-Z in connection with current output ESK II (can also be retrofitted, not for hazardous duty)
● multipole ring magnet with effective eddy-current brake
● optionally, seawater-proof indicator housing
● optionally, indicator housing of stainless steel 1.4404 (M9 SS)
Product Features of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
Sturdy stainless steel measuring cone
Operating pressure up to 44,100 psi
-321 to 572°F (-196 to 300°C) max operating temperature
Flow rates for liquids:
Lower limit: 0.47 gph
Upper limit: 26,418 gph
Flow rates for gases:
Lower limit: 0.002 scfm
Upper limit: 1736 scfm
Measuring range: 10:1
Accuracy: ±1.6 %
High application security, even with extremely small flows
Excellent long-term stability
Wide range of flange, threaded, clamp process connections
Resistant to extreme chemical, mechanical and thermal loads
All components replaceable
Heating jacket available for the measuring section
Highlights of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
• Simple, low-cost installation: Measure and display without auxiliary power supply
• Rugged stainless steel construction for high operating pressure up to 3000 bar / 44100 psi and extreme process temperatures of -200…+400°C / -328…+752°F
• Optionally available with PTFE/ceramic liner for acids and alkalis
• High application safety, even with extremely low flows
• Excellent long-term stability
• Modular and flexible to adapt to customer-specific applications
• SIL 2 certified
• International approvals for use in hazardous areas and nuclear power plants
Industries of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
Can be used in all industrial sectors, for example:
• Chemicals
• Petrochemicals
• Pharmaceutical
• Machinery
• Food & Beverage
• Oil & Gas
• Iron, Steel & Metals
• Power plants
• Pulp & Paper
• Water & Wastewater
Applications of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
• Continuous gas and liquid measurement
• Measurement of conductive and non-conductive media
• Industrial burner controlling
• Compressor monitoring
• Dry-run protection of pumps
Similar Models of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
H250/RR/M9/ESK
H250/RR/M9/ESK/EEK
H250/RR/M9
H250/RR/M9/ESK/K2/EEX
H250H/RR/M40
H250/RR/M40
H250/RR/M40R/ESK4
H250/RR/M40R/ESK-EX
H250/RR/M9/ESK/EEX
H250H/RR/M40/ESK
H250/RR/M10/EEX
H250/RR/M40/ESK4A
H250/PR/M9/K21
H250/PR/M40/K21
Version of Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters
Krohne H250/RRL/M40/ESK4/Ex Variable Area Flow Meters