MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Breif Description of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4544D – MTL5544D REPEATER POWER SUPPLY
single channel, 4/20mA, HART®
for 2- or 3-wire transmitters, two outputs
Product Overview of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
The MTL4544D MTL5544D provides a fully-floating dc supply for energising a conventional 2- or 3-wire 4/20mA transmitter located in a hazardous area, and repeats the current in other circuits to drive two safe-area loads. For HART 2-wire transmitters, the unit allows bi-directional transmission of digital communication signals superimposed on the
4/20mA loop current. Separately powered current sources, such as 4-wire transmitters, can be connected but will not support HART communication.
Technical SPECIFICATION of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
See also common specification
Number of channels
One
Location of transmitter
Zone 0, IIC, T4–6 hazardous area if suitably certified
Div. 1, Group A hazardous location
Safe-area output
Signal range: 4 to 20mA
Under/over-range: 0 to 24mA
Safe-area load resistance
@ 24mA: 0 to 360Ω
@ 20mA: 0 to 450Ω
Safe-area circuit output resistance: > 1MΩ
Safe-area circuit ripple
< 50µA peak-to-peak
Hazardous-area input
Signal range: 0 to 24mA (including over-range)
Transmitter voltage: 16.5V at 20mA
Transfer accuracy at 20°C
Better than 15µA
Temperature drift
< 0.8µA/°C
Response time
Settles to within 10% of final value within 50µs
Communications supported
HART (terminals 1 & 2, output Ch 1 only)
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
LED indicator
Green: power indication
Maximum current consumption (with 20mA signals)
96mA at 24V dc
Power dissipation within unit (with 20mA signals)
1.4W @ 24V dc
Terminals 2 to 1 and 3:
Uo=28V Io=93mA Po=651mW Um = 253V rms or dc
Terminals 1 to 3:
Simple apparatus ≤1.5V, ≤0.1A and ≤25mW; can be connected
without further certification into any IS loop with an open-circuit
voltage <28V
Similar Models of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Ordering Models of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Digital Input MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4501-SR 1ch DI failsafe solid-state output + LFD alarm
MTL4504 1ch DI relay output + LFD alarm + phase reversal
MTL4510 4ch DI solid-state output
MTL4510B 4ch DI multifunction solid-state output
MTL4511 1ch DI relay output
MTL4513 2ch DI solid-state output
MTL4514/B 1ch DI relay output + LFD alarm
MTL4516 2ch DI relay output
MTL4516C 2ch DI with changeover relay output
MTL4517 2ch DI relay output + LFD alarm
Digital Output MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4521 Loop powered solenoid driver
MTL4521L Loop powered solenoid driver IIC
MTL4523 Solenoid driver with LFD
MTL4523L Loop powered solenoid driver + LFD
MTL4523R Solenoid driver with LFD
MTL4523V/VL Solenoid/Alarm driver with voltage control
MTL4524 Switch operated solenoid driver
MTL4524S Switch operated solenoid driver, 24V override
MTL4525 Switch operated solenoid driver low power
MTL4526 2ch switch operated relay
Analogue Input MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4541 1ch 2/3 wire Transmitter repeater
MTL4541A 1ch Transmitter repeater, passive input
MTL4541AS 1ch Transmitter repeater, passive input, current sink
MTL4541B MTL4041B replacement
MTL4541P MTL4041P replacement
MTL4541S 1ch 2/3 wire Transmitter repeater, current sink
MTL4544 2ch 2/3 wire Transmitter repeater
MTL4544A 2ch Transmitter repeater, passive input
MTL4544AS 2ch Transmitter repeater, passive input, current sink
MTL4544B MTL4044 replacement
MTL4544D 2/3 wire transmitter repeater, dual output
MTL4544S 2ch 2/3 transmitter repeater, current sink
Analogue Output MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4546 1ch 4-20mA smart isolating driver + LFD
MTL4546C 1ch 4-20mA smart isolating driver + oc LFD
MTL4546Y 1ch 4-20mA smart isolating driver + oc LFD
MTL4549 2ch 4-20mA smart isolating driver + LFD
MTL4549C 2ch 4-20mA smart isolating driver + oc LFD
MTL4549Y 2ch 4-20mA smart isolating driver + oc LFD
Temperature Input MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4575 1ch Temperature converter with alarm
MTL4576-RTD 2ch Temperature converter, RTD
MTL4576-THC 2ch Temperature converter, THC
MTL4581 1ch mV/THC isolator for low-level signals
Pulse and Vibration MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4531 1ch vibration probe interface
MTL4532 1ch pulse isolator, digital or analogue output
MTL4533 2ch vibration probe interface
Fire and Smoke MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4561 2ch loop-powered, for fire and smoke detectors
General MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4599 Dummy isolator
MTL4599N General purpose feed-through module
Model No.
Module No. Bussed
Power MTL7000
Equivalent MTL7000
ATEX
Certificate
Number(s) MTL700
equivalent MTL700
ATEX
Certificate
Number(s) Typical
Application
MTL7710+ No Half of
MA15/D/1/SI 120V, 47-63Hz 140V
MA15/D/1TT/SI 120V, 47-63Hz 140V
MA15/D/2/SI 240V, 47-63Hz 280V
MA15/D/2TT/L 240V, 47-63Hz 280V
Ordering Models of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4113P Failsafe Proximity Detector input with LFD Baseefa certification to IEC61508 pending
MTL5113P Failsafe Proximity Detector input with LFD Baseefa certification to IEC61508 pending
MTL4043 Current Repeater – Current sinking Eutech assessed to IEC61508(smart transmitters)
MTL4041B-SR Current Repeater (smart transmitters) BASEEFA certified to IEC61508
MTL4041P-SR Current Repeater – high power BASEEFA certified to IEC61508(smart transmitters)
MTL4024-SR Solenoid / alarm driver BASEEFA certified to IEC61508
MTL4061-SR Fire & Smoke detector interface BASEEFA certified to IEC61508
MTL5021-SR Solenoid / alarm driver BASEEFA certified to IEC61508
MTL5022-SR Solenoid / alarm driver IIB gases BASEEFA certified to IEC61508
MTL5025-SR Solenoid / alarm driver low power BASEEFA certified to IEC61508
MTL5042-SR Current Repeater (smart transmitters) BASEEFA certified to IEC61508
MTL5061-SR Fire & Smoke detector interface BASEEFA certified to IEC61508
MTL4841/2 HART Multiplexers BASEEFA certified to IEC61508
E02011 Current Repeater Assessment to DIN 19250
MLDT28500 MTL data surge tester
MTL3046B,discontinued,replaced by:MTL5541
MTL3042,discontinued,replaced by:MTL5546Y
MTL5053,discontinued,replaced by:MTL5553
MTL5995,discontinued,replaced by:F101-PS
MTL3000 SERIES (200mA)
MTL4041A,discontinued,replaced by:MTL4541A
MTL4041B,discontinued,replaced by:4541B
MTL5042,discontinued,replaced by:MTL5541
MTL5061,discontinued,replaced by:MTL5561
MTL4842,discontinued,replaced by:MTL4852
FP32
MTL4521, MTL4521L, and MTL5521 loop powered, IIC gas group output
MTL5522 loop powered, IIB gas group output
MTL4523, MTL4523R, and MTL5523 powered, with LFD output
MTL4523L loop powered, with LFD output
MTL4523V, MTL4523VL, MTL5523V, MTL5523VL and
MTL4523Y powered, with LFD output
MTL4524, and MTL5524 powered, two control inputs
MTL4524S powered, switch and voltage controls
MTL4525, and MTL5525 low power output
TO ORDER SPECIFY of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
TP48-N Non-certified SPD – 1/2” NPT thread
TP48-I Non-certified SPD – 20mm ISO thread
TP48-G Non-certified SPD – G 1/2” (BSP 1/2 inch)
TP48-3-N Non-certified SPD – 1/2” NPT thread
TP48-3-I Non-certified SPD – 20mm ISO thread
TP48-3-G Non-certified SPD – G 1/2” BSP 1/2 inch
TP48-4-N Non-certified SPD – 1/2” NPT thread
TP48-4-I Non-certified SPD – 20mm ISO thread
TP48-4-G Non-certified SPD – G 1/2” BSP 1/2 inch
TP48-N-NDI Certified SPD – 1/2” NPT thread
TP48-I-NDI Certified SPD – 20mm ISO thread
TP48-G-NDI Certified SPD – G 1/2” (BSP 1/2 inch)
TP48-3-N-NDI Certified SPD – 1/2” NPT thread
TP48-3-I-NDI Certified SPD – 20mm ISO thread
TP48-3-G-NDI Certified SPD – 20mm ISO thread
TP48-4-N-NDI Certified SPD – 1/2” NPT thread
TP48-4-I-NDI Certified SPD – 20mm ISO thread
TP48-4-G-NDI Certified SPD – G 1/2” – BSP 1/2 inch
TP24/7-N-NDI Certified process transmitter surge protection device – 1/2” NPT thread
TP24/7-I-NDI Certified process transmitter surge protection device – 20mm ISO thread
TP24/7-G-NDI Certified process transmitter surge protection device – G 1/2” (BSP 1/2”)
TP24/7-N Non-certified process transmitter surge protection device – 1/2” NPT thread
TP24/7-I Non-certified process transmitter surge protection device – 20mm ISO thread
TP24/7-G
TP24/7 All
TP24/7-X-NDI
TP24/7-T-XNDI
TP-ACFF-N AC power & Foundation Fieldbus 1/2” NPT Thread
TP-ACFF-I AC power & Foundation Fieldbus 20mm ISO Thread
TP-AC420-N AC power & 4-20mA 1/2” NPT Thread
TP-AC420-I AC power & 4-20mA 20mm ISO Thread
TP-AC485-N AC power & Profibus DP (RS485) 1/2” NPT Thread
TP-AC485-I AC power & Profibus DP (RS485) 20mm ISO Thread
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
TP-P32-N-NDI Certified process transmitter surge protection device – 1/2” NPT thread
TP-P32-I-NDI Certified process transmitter surge protection device – 20mm ISO thread
TP-P32-G-NDI Certified process transmitter surge protection device – G 1/2” (BSP 1/2″)
TP-P32-N Non-certified process transmitter surge protection device – 1/2” NPT thread
TP-P32-I Non-certified process transmitter surge protection device – 20mm ISO thread
TP-P32-G Non-certified process transmitter surge protection device – G 1/2” (BSP 1/2″)
TP-P48-N-NDI Certified process transmitter surge protection device – 1/2” NPT thread
TP-P48-I-NDI Certified process transmitter surge protection device – 20mm ISO thread
TP-P48-G-NDI Certified process transmitter surge protection device – G 1/2” (BSP 1/2″)
TP-P48-N Non-certified process transmitter surge protection device – 1/2” NPT thread
TP-P48-I Non-certified process transmitter surge protection device – 20mm ISO thread
TP-P48-G Non-certified process transmitter surge protection device – G 1/2” (BSP 1/2″)
TS10-P 10 pair protection for PSTN applications
TS10-I 10 pair protection for ISDN or private wire applications
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Transmitters
MTL831B Analogue transmitter
Receivers
MTL838B-MBF Analogue receiver, RS485 and/or RS422 outputs for Modbus®
Analogue receiver accessories
PCS83 PC software configuration package
Process controller interface software
Contact Eaton’s MTL product line for details of software for interfacing with proprietary process controllers
Isolating interface units and earth leakage detectors
MTL3052 Digital isolator interface unit
MTL4220 Earth leakage detector
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
ENC8 General-purpose enclosure
ENC8SS General-purpose enclosure (stainless steel)
ENC83 Enclosure for MTL831B transmitter
ENC83SS Enclosure for MTL831B transmitter (stainless steel)
Literature of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Mounting accessories of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
ISP7000 Insulating spacer
THR2 Standard DIN rail, 35mm x 7.5mm
THR7000 T-section DIN rail, specially nickel plated,
35mm x 7.5mm, 1m length
Earthing/earth rail accessories of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
ETL7000 Earth terminal, DIN rail mounted
IMB57 Insulated mounting block (two needed)
ERB57S Earth rail bracket, straight
ERB57O Earth rail bracket, offset
ERL7 Earth rail, 1m length
ETM7 Earth terminal, pack of 50
Tagging accessories of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
TAG57 Tagging strip, 1m length
TGL57 Tagging strip labels, set of 10 x 0.5m
BRI7000 Barrier identifier
BIL7000 Barrier identification labels, sheet of 120
BIL7000L Barrier identification labels, A4 sheet of 126
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Enclosures
DX070 Enclosure for up to 9 x SD range SPDs
DX170 Enclosure for up to 22 x SD range SPDs
Accessories (replacement)
SD-F25 Replaceable fuse pack – 250mA standard(available in packs of 5)
RFA7050 Replaceable fuse pack – 50mA special(available in packs of 5)
RLA7000 Solid Link (available in packs of 5)
MTL4113P Failsafe Proximity Detector input with LFD Baseefa certification to IEC61508 pending
MTL5113P Failsafe Proximity Detector input with LFD Baseefa certification to IEC61508 pending
MTL4043 Current Repeater – Current sinking Eutech assessed to IEC61508(smart transmitters)
MTL4041B-SR Current Repeater (smart transmitters) BASEEFA certified to IEC61508
MTL4041P-SR Current Repeater – high power BASEEFA certified to IEC61508(smart transmitters)
MTL4024-SR Solenoid / alarm driver BASEEFA certified to IEC61508
MTL4061-SR Fire & Smoke detector interface BASEEFA certified to IEC61508
MTL5021-SR Solenoid / alarm driver BASEEFA certified to IEC61508
MTL5022-SR Solenoid / alarm driver IIB gases BASEEFA certified to IEC61508
MTL5025-SR Solenoid / alarm driver low power BASEEFA certified to IEC61508
MTL5042-SR Current Repeater (smart transmitters) BASEEFA certified to IEC61508
MTL5061-SR Fire & Smoke detector interface BASEEFA certified to IEC61508
MTL4841/2 HART Multiplexers BASEEFA certified to IEC61508
E02011 Current Repeater Assessment to DIN 19250
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MLDT28500 MTL data surge tester
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4500 Series Barriers MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
Ordering Models of MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
ICC MTL4544D MTL5544D Repeaters Power Supply Single Channel HART
MTL4544D MTL5544D Repeaters Power Supply Single Channel HART