ABB RPBA-01 PROFIBUS DP Adapter Module
General Information of ABB RPBA-01 PROFIBUS DP Adapter Module
PROFIBUS DP Adapter Module
ABB Drives RPBA-01 Profibus DP Adapter Module for ACS550 and ACS800 Series Inverters.
ABB Drives RPBA-01 Profibus DP Adapter Module for ACS550 and ACS800 Series Inverters.
RPBA-01
The RPBA-01 PROFIBUS DP Adapter module
The RPBA-01 PROFIBUS DP Adapter module is an optional
device for ABB drives which enables the connection of the drive to
a PROFIBUS network. The drive is considered as a slave on the
PROFIBUS network. Through the RPBA-01 PROFIBUS DP
Adapter module, it is possible to:ABB RPBA-01 PROFIBUS DP Adapter Module
ï give control commands to the drive
(Start, Stop, Run enable, etc.)
ï feed a motor speed or torque reference to the drive
ï give a process actual value or a process reference to the PID
controller of the drive
ï read status information and actual values from the drive
ï change drive parameter values
ï reset a drive fault.
The PROFIBUS commands and services supported by the
RPBA-01 PROFIBUS DP Adapter module are discussed in the
chapters DP-V0 communication and DP-V1 communication.
Please refer to the user documentation of the drive as to which
commands are supported by the drive.
The adapter module is mounted into an option slot on the motor
control board of the drive. See the Hardware Manual of the drive
for module placement options.
Configuration of the master station requires a type definition
(GSD) file. For DP-V0 communication, the file is available from
www.profibus.com or an ABB representative (the filename is
ABB_0812.GSD). For DP-V1 communication, the type definition
(GSD) file is available from an ABB representative (the filename is
ABB10812.GSD).
Compatibility of ABB RPBA-01 PROFIBUS DP Adapter Module
The RPBA-01 is compatible with all master stations that support
the PROFIBUS DP protocol.
Delivery check
The option package for the RPBA-01 PROFIBUS DP Adapter
module contains:
ï PROFIBUS DP Adapter module, type RPBA-01
ï two screws (M3x10)
ï this manual.
Bus connector X1
(see chapter
Electrical installation)
Diagnostic LEDs
(See chapter
Fault tracing)
PROFIBUS
master
Slave
stations
ABB Drive
ABB Drive Rotary node
address
selection switches
DIP switch for
selecting bus
termination
Fixing screw
(GND)
(frame)
Top view Side view
Overview
18
Warranty and liability information
The manufacturer warrants the equipment supplied against
defects in design, materials and workmanship for a period of
twelve (12) months after installation or twenty-four (24) months
from date of manufacturing, whichever first occurs. The local ABB
office or distributor may grant a warranty period different to the
above and refer to local terms of liability as defined in the supply
contract.
The manufacturer is not responsible for
ï any costs resulting from a failure if the installation,
commissioning, repair, alternation, or ambient conditions of the
drive do not fulfil the requirements specified in the
documentation delivered with the unit and other relevant
documentation
ï units subjected to misuse, negligence or accident
ï units comprised of materials provided or designs stipulated by
the purchaser.
In no event shall the manufacturer, its suppliers or subcontractors
be liable for special, indirect, incidental or consequential damages,
losses or penalties.
If you have any questions concerning your ABB drive, please
contact the local distributor or ABB office. The technical data,
information and specifications are valid at the time of printing. The
manufacturer reserves the right to modifications without prior
notice.
Overview of ABB RPBA-01 PROFIBUS DP Adapter Module
This chapter presents the steps to take during the start-up of the
RPBA-01 PROFIBUS DP Adapter Module. For more detailed
information, see the chapters Mechanical installation, Electrical
installation, and Programming elsewhere in this manual.
ABB RPBA-01 PROFIBUS DP Adapter Module